1 files changed, 190 insertions, 0 deletions

diff --git a/v4.0/src/CMD/COMP/COMP1.ASM b/v4.0/src/CMD/COMP/COMP1.ASM
new file mode 100644
index 0000000..b732543
--- /dev/null
+++ b/v4.0/src/CMD/COMP/COMP1.ASM
@@ -0,0 +1,190 @@
+        page    ,132                    ;
+        title   COMP.SAL - COMPARE A PAIR OF FILES
+;****************** START OF SPECIFICATIONS *****************************
+; MODULE NAME: COMP1.ASM
+;
+; DESCRIPTIVE NAME: Compare two files to show they are identical or not.
+;
+; FUNCTION:  The paths and names of each pair of files is
+;        displayed as the comparing process proceeds.  An
+;        error message will follow the names if:
+;            (1) a file matching the second filename can't be found,
+;            (2) the files are different sizes, or
+;            (3) either path is invalid.
+;
+;        During the comparison, an error message will appear for any
+;        location that contains mismatching information in the 2
+;        files.  The message indicates the offset into the files of
+;        the mismatching bytes, and the contents of the 2 bytes
+;        themselves (all in hex).  This will occur for up to 10
+;        mismatching bytes - if more than 10 compare errors are
+;        found, the program assumes that further comparison would be
+;        useless, and ends its compare of the 2 files at that point.
+;
+;        If all bytes in the 2 files match, a "Files compare OK"
+;        message will appear.
+;
+;        In all cases, after the comparing of 2 files ends, comparing
+;        will proceed with the next pair of files that match the 2
+;        filenames, until no more files can be found that match the
+;        first filename.  You are then asked if you want to compare
+;        any more files.  Replying "N" returns you to the DOS prompt
+;        (such as A>); a reply of "Y" results in prompts for new
+;        primary and secondary filenames.
+;
+;        In all compares, COMP looks at the last byte of one of the
+;        files being compared to assure that it contains a valid
+;        end-of-file mark (CTRL-Z, which is the hex character 1A).
+;        If found, no action is taken by COMP.  If the end-of-file
+;        mark is NOT found, COMP produces the message "EOF mark not
+;        found".  This is done because some products produce files
+;        whose sizes are always recorded in the directory as a
+;        multiple of 128 bytes, even though the actual usable data in
+;        the file will usually be a few bytes less than the directory
+;        size.  In this case, COMP may produce "Compare error"
+;        messages when comparing the few bytes beyond the last real
+;        data byte in the last block of 128 bytes (COMP always
+;        compares the number of bytes reflected in the directory).
+;        Thus, the "EOF mark not found" message indicates that the
+;        compare errors may not have occurred in the usable data
+;        portion of the file.
+;
+;        Multiple compare operations may be performed with one load
+;        of COMP.  A prompt, "Compare more files (Y/N)?" permits additional
+;        executions.
+;
+; ENTRY POINT: "START" at ORG 100h, jumps to "INIT".
+;
+; INPUT: (DOS command line parameters)
+;       [d:][path] COMP [d:][path][filenam1[.ext]] [d:][path][filenam2[.ext]]
+;
+;        Where
+;        [d:][path] before COMP to specify the drive and path that
+;                   contains the COMP command file.
+;
+;        [d:][path][filenam1[.ext]] -  to specify the FIRST (or primary)
+;                   file or group of files to be compared
+;
+;        [d:][path][filenam2[.ext]]  - to specify the SECOND file or group
+;                   of files to be compared with the corresponding file
+;                   from the FIRST group
+;
+;        Global filename characters are allowed in both filenames,
+;        and will cause all of the files matching the first filename
+;        to be compared with the corresponding files from the second
+;        filename.  Thus, entering COMP A:*.ASM B:*.BAK will cause
+;        each file from drive A:  that has an extension of .ASM to be
+;        compared with a file of the same name (but with an extension
+;        of .BAK) from drive B:.
+;
+;        If you enter only a drive specification, COMP will assume
+;        all files in the current directory of the specified drive.
+;        If you enter a path without a filename, COMP assumes all
+;        files in the specified directory.  Thus, COMP A:\LEVEL1
+;        B:\LEVEL2 will compare all files in directory A:\LEVEL1 with
+;        the files of the same names in directory B:\LEVEL2.
+;
+;        If no parameters are entered with the COMP command, you will
+;        be prompted for both.  If the second parm is omitted, COMP
+;        will prompt for it.  If you simply press ENTER when prompted
+;        for the second filename, COMP assumes *.* (all files
+;        matching the primary filename), and will use the current
+;        directory of the default drive.
+;
+;        If no file matches the primary filename, COMP will prompt
+;        again for both parameters.
+;
+; EXIT-NORMAL: Errorlevel = 0, Function completed successfully.
+;
+; EXIT-ERROR: Errorlevel = 1, Abnormal termination due to error, wrong DOS,
+;             invalid parameters, unrecoverable I/O errors on the diskette.
+;
+; EFFECTS: Files are not altered.  A Message will show result of compare.
+;
+; INTERNAL REFERENCES:
+;    ROUTINES: none
+;
+;    DATA AREAS:
+;       PSP - Contains the DOS command line parameters.
+;       WORKAREA - Temporary storage
+;
+; EXTERNAL REFERENCES:
+;    ROUTINES:
+;       SYSDISPMSG - Uses the MSG parm lists to construct the messages
+;                on STDOUT.
+;       SYSLOADMSG - Loads messages, makes them accessable.
+;       SYSPARSE - Processes the DOS Command line, finds parms.
+;
+;    DATA AREAS:
+;        COMPSM.SAL - Defines the control blocks that describe the messages
+;        COMPPAR.SAL - Defines the control blocks that describe the
+;               DOS Command line parameters.
+;
+; NOTES:
+;        This module should be processed with the SALUT preprocessor
+;        with the re-alignment not requested, as:
+;
+;               SALUT COMP1,NUL
+;
+;        To assemble these modules, the alphabetical or sequential
+;        ordering of segments may be used.
+;
+;        Sample LINK command:
+;
+;               LINK @COMP.ARF
+;
+;        Where the COMP.ARF is defined as:
+;
+;        COMP1+
+;        COMPPAR+
+;        COMPP+
+;        COMPSM+
+;        COMP2
+;
+;        These modules must be linked in this order.  The load module is
+;        a COM file, to be converted to COM with EXE2BIN.
+;
+; REVISION HISTORY:
+;            AN000 Version 4.00: add PARSER, System Message Handler,
+;                 Add compare of code page extended attribute, if present.
+;
+; COPYRIGHT: The following notice is found in the OBJ code generated from
+;            the "COMPSM.SAL" module:
+;
+;            "The DOS COMP Utility"
+;            "Version 4.00 (C) Copyright 1988 Microsoft"
+;            "Licensed Material - Property of Microsoft"
+;
+;PROGRAM AUTHOR: Original written by: Dave L.
+;                3.30 modifications by Russ W.
+;                4.0  modifications by: Edwin M. K.
+;                4.0  modifications by: Bill L.
+;****************** END OF SPECIFICATIONS *****************************
+        PAGE
+;           $SALUT (4,13,18,36)
+            IF1
+                %OUT COMPONENT=COMP, MODULE=COMP1.ASM
+            ENDIF
+
+CSEG        segment PARA public  'CODE' ;AN000;
+            assume cs:CSEG,ds:CSEG,es:CSEG,ss:CSEG ;AS SET BY DOS LOADER
+PSP_HEADER  EQU  $                 ;START OF PROGRAM SEGMENT PREFIX AREA
+            org  02h
+MEMORY_SIZE LABEL WORD
+            PUBLIC MEMORY_SIZE
+
+            org  5Ch
+FCB         LABEL BYTE
+            PUBLIC FCB
+
+            org  80h
+PARM_AREA   LABEL BYTE
+            PUBLIC PARM_AREA
+
+            org  100h
+            EXTRN INIT:NEAR        ;"INIT" IS IN COMP2.SAL
+START:      jmp  INIT              ;DEFINE THE DOS ENTRY POINT
+
+CSEG        ENDS
+            END  START
+
\ No newline at end of file